EN
Converting powder single superphosphate (SSP) to granulated SSP (GSSP) usually requires feed preparation, a granulator, drying and cooling equipment, screens, an oversize crusher, and a recycle system. Conveying, dust collection, packaging, and controls must support the added circuit. The existing rock grinding, acidulation, and curing sections may remain in service if their capacity and product quality suit the conversion.
Shanghai Yingyong Machinery (SYM) supplies SSP/GSSP production equipment and integrated plant engineering. For an existing powder SSP plant, the project should begin with the available cured feed and required saleable output. Those two conditions determine what the new equipment must handle.

Often, the conversion adds a granulation circuit downstream of the existing SSP process. In the conventional route, cured SSP passes through lump breaking, rotary drum granulation, drying, cooling, and screening before storage or dispatch. [1]
Check the condition of the feed before ordering equipment. Moisture, residual free acidity, particle size, and lumps influence handling and granulation. Confirm that upstream production and curing can supply the new circuit consistently. If powder SSP sales will continue, allow for a feed split and separate handling rather than assuming the entire powder output will become GSSP.
The following equipment forms the basis of a conventional wet granulation conversion. Final selection depends on feed behavior, target granule quality, and the equipment already installed.
| Equipment | Function | What to specify |
| Feed hopper, lump breaker, and feeder | Prepare cured SSP and deliver a steady feed | Lump size, moisture range, flow behavior, and fresh feed rate |
| Mixer or conditioner where needed | Distribute liquid and prepare the feed | Whether conditioning is necessary and which liquid addition suits the material |
| Rotary drum granulator | Form granules from powder and recycled material | Feed characteristics, product size range, and expected recycle flow |
| Rotary dryer and heat source | Remove moisture added during granulation | Water evaporation load, fuel availability, and product temperature limits |
| Rotary cooler | Prepare dried granules for handling and storage | Inlet temperature, bagging temperature target, and local ambient conditions |
| Screens, oversize crusher, and recycle equipment | Separate saleable granules and return off-size material | Screen cut sizes, crushing duty, and total circulating load |
| Conveyors, elevators, and packing equipment | Transfer and dispatch finished fertilizer | Layout, transfer heights, granule breakage, and bagging capacity |
| Exhaust treatment and process controls | Manage emissions and coordinate the circuit | Gas conditions, dust load, instrumentation, and existing system capacity |
Granulation performance depends on the equipment around it. Uneven feed or liquid addition can produce an unstable size distribution. Excess moisture increases the dryer duty, while weak granules may break during transfer and add to the recycle load.
SYM supplies rotary drum granulators together with dryers, coolers, screening, and material handling equipment. Its dryer uses internal lifting flights to bring the material into contact with the drying gas. Selecting these machines together helps the project address moisture removal, cooling, and particle handling as one circuit.

Define capacity as saleable GSSP output and ask the supplier to show the fresh feed and recycle flows separately. Equipment inside the recycle circuit must accommodate the material actually passing through it. A granulator rating alone does not establish the output of the finished line.
Review the available electrical supply, drying fuel, process water, and any steam requirement. Also check building space, foundations, access for maintenance, and the capacity of shared conveyors and packing equipment. Dryer sizing should reflect the evaporation load; cooler selection should account for the hottest expected operating conditions.
Assess exhaust treatment for each emission source. SSP production can release both fertilizer dust and fluoride gases, so a dust collector should not be assumed to provide all required gas treatment. [1] Check the existing system before connecting additional exhaust streams, including changes in flow, temperature, moisture, and pollutant loading.
Agree on the feed conditions and product acceptance criteria before equipment selection is finalized. These should cover saleable throughput, particle size distribution, moisture, granule strength, temperature at bagging, and the applicable nutrient specification. Adding water or other materials must be considered in the finished product composition.
Set a commissioning plan that checks the full circuit under agreed operating conditions. Record fuel and electricity consumption, recycle flow, and off-spec production alongside finished product quality. Where feed behavior is uncertain, discuss material testing before committing to the final configuration.
SYM provides process design, equipment manufacturing, installation, and commissioning services for fertilizer plants. Its portfolio covers feeding and mixing through granulation, drying, cooling, screening, and packaging. For a powder SSP conversion, this gives customers a basis for discussing the added circuit and its connections to the existing plant with one engineering and equipment supplier.
Planning to add GSSP production? Send SYM your current SSP output, cured feed analysis, target granule specifications, available utilities, and plant layout. Our engineers can discuss the equipment scope and integration requirements for your project.
[1] US EPA. AP-42 Section 8.5.1 Normal Superphosphates. Process description and emission sources. https://www.epa.gov/sites/default/files/2020-09/documents/8.5.1_normal_superphosphates.pdf
Submit Request